Hot Tub Repair in Fox River Grove and the Northwest Suburbs
Not heating, won't turn on, tripping the breaker or flashing a code? I repair all makes and models, and I'll explain what I found in plain terms.
My name is Lucas Medansky, and I run Home and Spa Solutions out of Fox River Grove. After working three years as a service tech, I started this business with the goal to grow a brand people can depend on. I pride myself on my work, attention to detail and care for my customers. I repair hot tubs of all makes and models within about 60 miles of Fox River Grove, from older tubs with air-button controls to newer digital systems.
Most hot tub problems come down to a short list of systems: power, water flow, heat, controls and plumbing. A tub that won't heat might have a dirty filter, a bad sensor, a failed heater element or a relay on the board that quit. Before I replace anything, I test to find the actual cause, because swapping parts on a guess wastes your money and your time. If the fix is bigger than it looks, I'll tell you what I found and what your options are.
Common reasons people call me
- The water is cold or won't hold temperature
- No power, or the topside panel is blank
- The GFCI breaker trips on reset or when a pump starts
- Jets are weak, surging or not running at all
- The water level keeps dropping, or there's water under the cabinet
- Grinding, screeching or humming from the equipment bay
- An error code on the panel, like FLO on Gecko or dr on Balboa
How a repair visit usually goes
Start with what you've seen
I ask what the tub is doing, when it started and whether anything changed, like a storm, a refill or a cold snap. A photo of the panel or the code helps.
Test, don't guess
I check power, flow, heat and controls in order, using a meter and the control system's own diagnostics, until the problem is narrowed down to one part or connection.
Explain the fix
I show you what failed and explain the repair in plain terms, including whether it's worth repairing the part or replacing it.
Repair and run it
After the repair, I run the tub through its cycles, check for leaks and check that it heats and circulates the way it should.
Before you call, check the filter and the breaker
A dirty filter is one of the most common causes of weak jets and heating codes, so rinse it or swap in a clean one first. Then check the GFCI breaker: reset it once, and if it trips again, leave it off. Write down any code on the panel, because it tells me where to start.
Hot Tub Repair: common questions
Do you work on my brand of hot tub?
Yes. I repair all makes and models. Most hot tubs share the same basic parts: pumps, a heater, a control system, a topside panel and plumbing. The brand on the cabinet matters less than the control system inside, which is often made by a company like Balboa or Gecko. If you can tell me the brand, the model and roughly how old the tub is, that helps me plan the visit.
Why is my hot tub not heating?
The usual causes are a dirty filter, low water, an air lock after a refill, a tripped high limit, a failed temperature sensor, a bad heater element or a relay on the board that no longer closes. On 120 volt plug-in tubs, the heater often shuts off while the jets run on high, which is normal. Check the filter and the water level first. If the panel shows a code, write it down before you reset anything.
Why does my hot tub keep tripping the GFCI?
A GFCI trips when it senses current leaking to ground. In a hot tub that usually means water got where it shouldn't: a heater element with a cracked sheath, a pump motor with a failed shaft seal, a wet connection or wiring chewed by mice. Sometimes the breaker itself is worn out. Reset it once. If it trips again, leave it off and call me. Resetting it over and over won't fix the cause.
Is my old hot tub worth repairing?
Often, yes. Pumps, heaters, boards and topside panels can all be replaced, and many older control systems have newer replacement packs that fit. What matters more is the shell, the cabinet and the frame. If the shell is cracked, the frame under it is rotted, or the foam is soaked through from a long-running leak, a repair may not make sense. I'll tell you what I see so you can decide.
Where I do hot tub repair
Based in Fox River Grove, I cover about 60 miles around it. Towns with their own page:
Other services
Diagnostics and Error Codes
A code points to a system, not a part. I test to find the actual cause before anything gets replaced.
Learn morePump and Motor Repair
Humming, screeching, leaking or dead pumps. Seals, bearings, motors and complete pump replacement.
Learn moreCircuit Boards and Controls
Blank topside panels, burnt relays, no heat, storm and mouse damage. Board and panel replacement.
Learn moreRequest a quote
Tell me what is going on with your hot tub and I will get back to you. A photo of the equipment label or the error code helps. In a hurry? Call (224) 357-7149.